From 95dc36850b2182e73b43bbf86a13827abecff19d Mon Sep 17 00:00:00 2001
From: Stefan Kremser <stef.1497@gmail.com>
Date: Sun, 14 Oct 2018 16:56:45 +0200
Subject: [PATCH] Update A_config.h

---
 .../DSTIKE_Deauther_OLED_v1-v1.5/A_config.h   | 54 +------------------
 1 file changed, 1 insertion(+), 53 deletions(-)

diff --git a/configs/DSTIKE_Deauther_OLED_v1-v1.5/A_config.h b/configs/DSTIKE_Deauther_OLED_v1-v1.5/A_config.h
index 52c1782..05b6062 100644
--- a/configs/DSTIKE_Deauther_OLED_v1-v1.5/A_config.h
+++ b/configs/DSTIKE_Deauther_OLED_v1-v1.5/A_config.h
@@ -11,72 +11,20 @@
 // =========================== //
 
 // ===================== LED CONFIG ==================== //
-/* = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
-    Uncomment the type of LED  you're using
-    Only one of them can be defined at a time!
-   = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = */
 #define DIGITAL_LED
-//#define RGB_LED
-//#define NEOPIXEL_LED
-
-/* = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
-    Adjust following settings for your type of LED
-    you can ignore the rest of the #define's
-   = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = */
-   
-// === Settings for Digital LED and RGB LED === //
 #define LED_ANODE false   // common vcc (+)
 #define LED_PIN_R 16      // NodeMCU on-board LED
 #define LED_PIN_G 255     // 255 = LED disabled
 #define LED_PIN_B 2       // ESP-12 LED
 
-// === Settings for RGB LED and Neopixel LED === //
-#define LED_MODE_BRIGHTNESS 10 // brightness of LED modes 
-
-// === Settings for Neopixel LED === //
-#define LED_NEOPIXEL_NUM 1
-#define LED_NEOPIXEL_PIN 9
-#define LED_NEOPIXEL_MODE NEO_GRB + NEO_KHZ800
-//   NEO_KHZ800  800 KHz bitstream (most NeoPixel products w/WS2812 LEDs)
-//   NEO_KHZ400  400 KHz (classic 'v1' (not v2) FLORA pixels, WS2811 drivers)
-//   NEO_GRB     Pixels are wired for GRB bitstream (most NeoPixel products)
-//   NEO_RGB     Pixels are wired for RGB bitstream (v1 FLORA pixels, not v2)
-//   NEO_RGBW    Pixels are wired for RGBW bitstream (NeoPixel RGBW products)
-
 // ===================== DISPLAY CONFIG ==================== //
 #define USE_DISPLAY true // default display setting
 
-/* = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
-    Adjust the pins to match your setup
-    Comment out the buttons you don't use.
-   = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = */
 #define BUTTON_UP 12
 #define BUTTON_DOWN 13
 #define BUTTON_A 14
 
-//#define BUTTON_LEFT 12
-//#define BUTTON_RIGHT 13
-//#define BUTTON_B 10
-
-/* = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
-    Uncomment the type of display you're using
-    Only one of them can be defined at a time!
-   = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
-    0x3c = I2C address
-    SDA = GPIO 5 (D1)  
-    SCL/SCK = GPIO 4 (D2) */
 #define DEAUTHER_DISPLAY SSD1306Wire display = SSD1306Wire(0x3c, 5, 4); // for 0.96" OLED
-//#define DEAUTHER_DISPLAY SH1106Wire display = SH1106Wire(0x3c, 5, 4); // for 1.3" OLED
-
-/*  RST = GPIO 5 (D1)
-    DC = GPIO 4 (D2)
-    CS = GPIO 15 (D8) or GND
-    SCK/SCL = GPIO 14 (D5)
-    SDA/MOSI = GPIO 13 (D7) */
-//#define DEAUTHER_DISPLAY SSD1306Spi display = SSD1306Spi display = SSD1306Spi(5, 4, 15); // for 0.96" OLED with SPI
-//#define DEAUTHER_DISPLAY SH1106Spi display = SH1106Spi(5, 4, 15); // for 1.3" OLED with SPI
-
-//#define FLIP_DIPLAY // uncomment that to flip the display vertically
 // ========================================================= //
 
-#endif
\ No newline at end of file
+#endif